A filter closing element is a turned accessory that closes or retains a filter insert. It is not a complete filter, and it is not a filter station. SUNHY produces this type of part from the customer’s current drawing, together with the stated material, thread, finish and quality requirements. This note is for purchasing and supplier-quality engineers who need to enquire for the component — and for related turned parts on the same programme — without implying a finished filter in the RFQ.

The form shown on the filter closing elements page is a capability example, not a stock item. Colour in the model does not represent the specified material or the specified zinc-plated finish. The catalogue type code is a SUNHY designation for that example; it does not replace the customer’s item number or drawing revision.

What the catalogue example actually is

SH-ST-FE-01 is shown as a steel closing element for a filter insert, in S355J2, zinc plated. The condition of the steel, the thread, the finish and the inspection are taken from the customer’s drawing. No thread size is published for this example; the thread is read from the print. Other closing-element geometries are reviewed when a drawing is provided.

The typical manufacturing route for parts of this type is CNC turning. A combined route may be considered where volume supports it. 100-piece samples are typically available in 45 days; the window is confirmed with each enquiry.

A closing element, not a complete filter

SUNHY does not manufacture complete filters or filter stations. The part quoted is the closing element, or another named accessory, made to the agreed print. An RFQ that asks for “a filter” or “a station” cannot be treated as an enquiry for a finished appliance. Write the item as a component, and send the drawing for that component.

The same limit of supply is used for other gas-equipment accessories on this site — including diaphragm housings and slam-shut internals. A material certificate or an inspection record for a closing element is evidence for that part, to the scope agreed in the order. It is not a certificate for a complete filter.

Thread, seat and the features that actually close the insert

The features that close or retain the insert — a thread, a shoulder, a seat, a hex or other driving form, an O-ring groove if one is present — are taken from the print. Because no thread size is published for the catalogue example, the RFQ has to carry the thread system, size, pitch and class of fit, and the condition in which the thread will be gauged. Sealing or locating diameters should be identified if they are critical to function, together with any surface-condition note that applies after plating.

These details are what make the part usable in the customer’s filter assembly. They are also what distinguish a made-to-print accessory from a generic plug or cap. Unspecified or conflicting features are listed as open items before a route is proposed.

Related turned parts on the same programme

Related rotationally symmetric parts — additional turned accessories on the same filter or station programme — can be reviewed when the drawings are provided. Each item is still a made-to-print component. If steel connecting stubs, threaded adapters or other accessories sit on the same assembly, those drawings can be included in the same enquiry.

Finish, gauging and documents

Zinc plating is the finish shown for the catalogue example. Other finishes can be reviewed when they are specified, and are confirmed with the drawing. If the thread must be gauged after plating, or if a particular coating thickness or after-treatment is required, that belongs in the RFQ. Thread gauging on made-to-print parts and materials and finishes on gas-equipment prints set out the same rule.

The inspection plan is written against the drawing and the order. EN 10204 3.1 and other documents are confirmed with the order scope when requested; they are not assumed inclusions. PPAP and IMDS are reviewed when a project requires them and are confirmed in the quotation. Quality-system evidence is per order. See documents confirmed per order.

What to send with the RFQ

Send the current drawing revision, the material and condition, the thread call-out, the finish, the final gauging condition, and the documents required. State that the part is a closing element or a related turned accessory, not a complete filter. Use the request form or email anna@sunhyings.com. A wider checklist is in what to include in a made-to-print RFQ.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.