On a made-to-print fastener, the thread is a drawing-controlled characteristic, not a shop-floor default. Size, pitch, thread system and class of fit have to be read from the current revision, together with the condition in which the thread will finally be gauged. This note is for purchasing and supplier-quality engineers who need metric or inch threads produced to the print, including after coating when the drawing requires it.

SUNHY reviews threads on bolts, screws and studs, weld nuts, special nuts and installation elements, and on threaded gas-equipment accessories, against the customer drawing. Catalogue type codes and example sizes on this site do not replace the thread call-out on that drawing.

What the print has to state

A complete thread call-out names the system, the size, the pitch and the tolerance class or class of fit. ISO metric threads are common on European programmes; Unified and other inch-series threads are reviewed when they are specified. Pipe threads such as G 3/4 or G 5/4 (G 1¼), which appear as examples on some gas-equipment pages, are likewise taken from the print. They are not a default for every enquiry.

Internal and external threads, left-hand threads, fine or special pitches, and any note on useful thread length or engagement should be visible on the revision that is to be quoted. If a 3D model is supplied, it helps the review of form and tool access, but it does not override the 2D thread data unless the enquiry says so in writing.

Class of fit is not a commercial assumption

Tolerance classes such as 6g and 6H, or Unified classes such as 2A and 2B, are taken from the drawing. A looser or tighter class is not substituted to make coating or gauging more convenient. “A standard commercial thread” is not a substitute for a missing class. If the class has not yet been assigned, that is an open item and should be closed before production, not inferred from a catalogue fastener.

Where a special thread, a non-standard pitch, or a thread that has to be cut rather than rolled is required, that condition belongs in the RFQ so that the process route can be set accordingly. Rolled or cut threads are process decisions; they are proposed against the print and the volume, not assumed.

Gauging before and after coating

Go / no-go thread gauging is the usual method referred to on this site. The controlling point is when that gauging is required to be carried out. A coating adds thickness. An external thread that was within limits before plating can sit outside the gauge after the coating is applied, and an internal thread can become tight. If the drawing or the specification requires the finished, coated thread to gauge, that condition has to be written into the enquiry and into the inspection plan.

Gauging after coating is included when it is specified, not automatically on every lot. Over-tapping, under-tapping, or an adjustment to the coating process are not informal shop practices; they are process decisions that have to follow the print and be agreed before serial release. If only the uncoated thread is to be gauged, or if both conditions apply to different characteristics, say so.

Inch and metric systems are not mixed on the same characteristic, and a conversion is not offered as a substitute for the call-out on the print. If a programme uses metric threads on some items and Unified or pipe threads on others, each drawing is reviewed on its own terms. Gauge equipment and acceptance follow the system that is specified.

Related conditions that affect the thread

Heat treatment, the coating system and any subsequent welding or installation step can all change the thread condition. On weld nuts, the final thread condition after welding or after coating should be stated so that the route can be set accordingly; that point is also made in the note on weld nuts and special nuts. On high-strength parts, the coating system and any hydrogen-embrittlement control should be named with the thread requirement — see coatings for high-strength fasteners.

Dimensional checks of related features — under-head radius, runout, pitch diameter as a measured value rather than a gauge result, or a specific gauge type — are added to the plan when the drawing or the order requires them.

What to write in the RFQ

Include the thread system, size, pitch and class of fit as they appear on the current revision, and state the final gauging condition, including after coating if that is required. If a particular gauge standard or a measured pitch-diameter method is already decided, name it. Send the drawing with the request form or to anna@sunhyings.com. A wider list of enquiry items is in what to include in a made-to-print RFQ.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.