A set screw or a grub screw is a short, usually headless fastener whose function lives in the point, the drive and the material condition. On a made-to-print order those features are taken from the current revision. A catalogue set-screw type, a preferred stainless grade, or a workshop socket that happens to fit is not a substitute for the dimensions, the property class and the finish that the print actually shows.
SUNHY reviews these parts in the bolts, screws and studs family, including fully threaded and partially threaded items, against the customer drawing. The notes on point styles, chamfers and pilots and on drive recesses and socket gauging belong beside this one, because those two ends are usually the controlling features. This article looks at how a set-screw print should be written so that it can be quoted without inventing a standard type.
Point, drive and length have to be stated together
A complete call-out names the point style (cup, cone, dog, flat, knurled cup, or a special form) with its controlling dimensions, the drive type and size, the thread, and the overall or useful length. Those numbers have to be consistent. A deep socket and a long dog point on a short screw can leave too little material; a large chamfer can leave too little useful thread. Those conflicts are flagged before tools are committed. “Set screw, cup point” without dimensions is not complete, even when the thread size is given.
The thread may be complete along the whole length, or it may stop short of the point or the drive. Useful length, runout and any unthreaded region follow the same rules as on other fasteners, as described in the notes on useful thread length and on thread runout. A knurl on a cup point, or a pilot in front of the thread, is a characteristic in its own right and is not added because a similar set screw has one.
Material, class and stainless grades
Property class, material grade and condition are print call-outs. A hardened carbon-steel set screw is not assumed, and an A2 or A4 stainless grade is not a default when the print is silent. If 304, 316, 410 or another stainless grade is specified, the condition, any magnetism requirement and the finish are taken from the same revision. Those points are developed further in the note on stainless fasteners in 304 (A2), 316 (A4) and 410. A substitution “to what we usually hold in stainless” is not offered.
Heat treatment, when it is specified or when it is required to meet a property class, belongs in the agreed route, as in the note on heat treatment. Case hardening, if the print calls it up, is a specified process with a case depth and a hardness, not an informal shop practice; that subject is taken up in the note on carburizing and case hardening. Certificates and any EN 10204 3.1, PPAP or IMDS evidence are confirmed per order when required, as already described in the existing material and order-document notes.
Process, coating and gauging
Set screws may be headed and rolled, or they may be produced on a turned or a ground route when the point, the drive or the tolerance requires it. The method is a process decision and is stated rather than assumed. A machined sample is not approval of a later headed route, or the reverse. A change of point punch, of socket punch, or of threading method is a process change and is re-validated before serial release — see the notes on cold-heading tooling and on secondary operations.
The thread and the drive are gauged as specified, including after coating when that condition is required. A dark oxide, a zinc system or a plain finish is taken from the print, not from a catalogue preference. On high-strength carbon or alloy parts, any hydrogen-embrittlement control is named with the coating. Informal oiling of the socket or the thread is not part of the route unless the specification allows it.
Inspection of both ends
Point dimensions, drive gauges, thread gauges, hardness and, when specified, a tightening or a holding check are used when the print or the order requires that evidence, not automatically in every possible form. If a particular gauge or a first-article layout of the point and the socket is already decided, name it. A visual check that “there is a cup and a hex socket” is not a substitute for the diameters and the depths that are written on the print.
First-article or layout inspection, when required, should be planned on the production-intent route, including the coating state in which the thread and the drive will be gauged. Measuring a soft, uncoated, fully machined sample and treating the result as approval of a headed, heat-treated and coated series part is a category error. That rule is the same as in the note on first-article inspection.
What to write in the RFQ
Name the point style and its dimensions, the drive type and size, the thread, the length, the material or stainless grade, the property class or condition, the finish, any after-coating gauging, the volume and the documents you need, all as they appear on the current revision. Send the print with the request form, not a request to match a catalogue set-screw type from a photograph.
Send the print. The scope is confirmed before quote.
Email the current drawing revision, or use the request form. Unspecified points will be flagged before production rather than assumed.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.