An undercut, a neck or a groove on a made-to-print fastener can be a drawing-controlled feature: a relief under the head, a thread undercut, a snap-ring groove, a break-neck, or a special recess. When the print states it, the diameter, the width, the radii and the position are requirements. They are not a leftover of a heading die, and they are not added as a convenience so that a thread can be run closer to a shoulder than the drawing allows.
SUNHY reviews these features on bolts, screws and studs and on turned parts, against the customer drawing. The notes on under-head radius and bearing face, on thread runout and on shank diameter and grip length belong beside this one. This article looks at how a neck or a groove should be written, and at why an informal undercut is a process change.
What has to be visible on the revision
A complete call-out names the diameter, the width or length, the position, and the radii or chamfers at each side of the groove or neck. A break-neck, if it is intentional, will also have a remaining diameter and, when specified, a break load or a location of failure. “Undercut as required to thread” or “a small neck under the head” is not a dimension. If a standard groove (for a retaining ring, a seal or a similar element) is used, the enquiry should name the standard and the size when the print itself does not.
Where the undercut sits next to a thread, a bearing face or an under-head radius, the features have to be consistent. A sharp thread runout into a fillet, or a neck that removes the radius the print requires, is a conflict and is flagged. The undercut is not used to hide a method that cannot otherwise meet the drawing. That is the same discipline already applied to under-head geometry in the existing note on bearing face and radius.
Process: heading, turning and later changes
A neck can be formed in the heading tools, turned as a secondary operation, or produced on a fully machined route. The choice is a process decision and is stated rather than assumed. Formed and machined grooves do not have the same radii, the same surface or the same concentricity, even when the diameter is similar. A machined sample with a turned undercut is not approval of a later formed neck, or the reverse. Adding an undercut that the print does not show, or moving one that it does, is a process change and is re-validated before serial release — see the notes on cold-heading tooling and on secondary operations.
A break-neck or a reduced section that is intended to fail at a defined location is a functional characteristic, not only a machining convenience. Its remaining diameter, surface and any heat-treatment condition belong in the review. Informal polishing or a change of radius after samples have been approved is not a permitted adjustment.
Heat treatment, coating and stress
A sharp undercut is a stress raiser. Heat treatment, particularly on higher property classes, can make that geometry more sensitive, and coating or hydrogen-embrittlement control may be named on the same part. Those conditions stay with the print and with the agreed route; they are not informal extras. The existing notes on heat treatment and on coatings for high-strength fasteners apply here as they do on a plain shank.
Coating builds in a groove as well as on a thread. If a snap-ring groove, a seal diameter or a remaining neck diameter must be met after coating, that condition should be stated. Over-cutting “to make plating work” is not an informal shop practice. Distortion of a thin neck during heat treatment, and any subsequent straightening, are part of the review when the geometry makes them relevant.
Inspection of the neck or groove
Diameter, width, position, radii, or a layout of the undercut are used when the print or the order requires that evidence, not automatically in every possible form. If a particular gauge, a profile projector, or a first-article measurement is already decided, name it. A visual check that “there is a neck” is not a substitute for a remaining diameter that is written on the print. Break-load or functional checks, when they are required, are confirmed per order, not assumed from a similar part.
First-article or layout inspection, when required, should be planned on the production-intent route, including the method used to produce the undercut and the coating state in which diameters will be checked. Measuring a soft, fully machined sample and treating the result as approval of a headed, heat-treated and coated series part is a category error. That rule is the same as in the note on first-article inspection.
What to write in the RFQ
Quote the neck, undercut or groove with its diameter, width, position and radii, together with the thread, the under-head features, the material, the property class, the finish, any after-coating condition, the volume and the documents you need, all as they appear on the current revision. If a retaining-ring or seal standard applies, name it. Send the print with the request form.
Send the print. The scope is confirmed before quote.
Email the current drawing revision, or use the request form. Unspecified points will be flagged before production rather than assumed.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.