An intermediate anneal, a spheroidize, a stress relief, or another in-process softening step is a process operation. On a made-to-print fastener it belongs in the agreed route when it is used, just as heading, threading, quench and temper, or case hardening do. It is not an informal shop heat “to make the next blow easier”, and it is not omitted from the documented sequence because it is intermediate. If the print itself requires a particular annealed condition in the finished part, that condition is a requirement, not only a process aid.

SUNHY reviews these steps on bolts, screws and studs, on turned parts and on other made-to-print components, against the customer drawing and the proposed route. The notes on heat treatment, on cold-heading tooling and on carbon and alloy steels belong beside this one. This article looks at how in-process softening should be treated in a quotation and in later changes.

Finished condition and process condition are different

Some prints require a finished annealed, solution-treated, or stress-relieved condition, with a hardness or a microstructure. That is a drawing requirement and is inspected when specified. Other anneals exist only so that a wire or a blank can be headed, extruded, or machined, after which a later quench and temper or a case treatment sets the finished condition. Those in-process steps still have to be named in the route, because they affect structure, decarburization risk, and the starting point of the later heat treatment. They are not invisible just because the finished hardness will be checked later.

Stainless and alloy parts may need an intermediate anneal for a different reason — work-hardening in an austenitic grade, or a difficult reduction in an alloy steel. The need is reviewed, as in the notes on stainless fasteners and on carbon and alloy steels, but it does not authorise a finished condition that the print does not require, and it does not authorise a grade change to avoid the anneal.

Where the step sits in the sequence

Softening may be applied to the wire or the bar before heading, to a partially formed blank, or after a difficult reduction and before threading. Each position leaves a different structure for the next operation and for the final heat treatment. That position is part of the agreed route and is stated rather than assumed. A sample that was produced from already-soft mill wire is not automatically approval of a later route that adds a mid-process anneal, or the reverse, when the change can affect the finished structure or the dimensions.

A change that adds, removes, or moves an anneal is a process change and is re-validated before serial release, in the same spirit as a die change or a change of threading method — see the notes on cold-heading tooling, on secondary operations and on prototype samples and series production. Informal extra anneals “because this lot feels hard” are not a made-to-print practice.

Atmosphere, decarburization and later heat treatment

The atmosphere, the temperature and the time of an anneal can affect decarburization, scale and surface condition. If the print or a referenced specification limits decarburization or requires a particular surface, those limits apply to the whole route, including intermediate steps, not only to the final harden and temper. Subsequent quench and temper, or a specified case treatment, starts from the structure the anneal left behind. Those later treatments remain as specified, as in the notes on heat treatment and on carburizing and case hardening.

Coating and any hydrogen-embrittlement control are still named with the finish of the finished part. An intermediate anneal does not replace them, and it does not excuse an informal bake or a change of coating. The existing coatings note describes that control on high-strength parts.

Inspection and records

Finished hardness, tensile, microstructure, or decarburization checks are used when the print or the order requires that evidence, not automatically in every possible form. In-process hardness or structure checks, when they are part of the agreed control plan, belong with the lot and with the route, not only with a verbal shop note. If a particular certificate, a heat-treatment report, or a first-article record of the route is already decided, name it. Certificates and any EN 10204 3.1 evidence are confirmed per order when required, as in the notes on material grade and certificates and on order documents.

First-article inspection, when required, should be planned on the production-intent route, including any intermediate anneal that will be used in series. Measuring a part that skipped the anneal, or that used a different wire condition, and treating the result as approval of the series route is a category error. That rule is the same as in the note on first-article inspection.

What to write in the RFQ

Quote the finished material condition, any specified anneal, hardness or microstructure, the grade, the later heat treatment or case treatment if it is required, the coating, the documents you need, the volume and the rest of the part as they appear on the current revision. If a customer heat-treatment specification already exists, attach or name it. Send the print with the request form.

Send the print. The scope is confirmed before quote.

Email the current drawing revision, or use the request form. Unspecified points will be flagged before production rather than assumed.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.