Connecting stubs used on gas-equipment prints often carry a sealing face: a flat, a cone, a spigot, or another form that will later meet a gasket, an O-ring or a mating metal face. Those faces are characteristics of the component. They are inspected as the current revision requires. They do not make the stub a complete regulator, a valve, a filter or a station, and a face that is correctly machined is not a type test of an assembled product. SUNHY quotes the stub as a part, in the same scope already described for brass connecting stubs and union nuts and for steel connecting stubs and threaded adapters.
What has to be visible on the revision
A complete call-out shows the form of the face, its diameter or cone angle, any width of a sealing land, the roughness, and any flatness, squareness or runout relative to a datum. If a standard already defines the face — for example a named thread-and-face combination on a gas-equipment accessory — that standard should be cited. “Sealing face, usual finish” is not complete. A type code, including any SH- or SH-BR example used only as an illustration, does not replace the view.
The sealing face is a different characteristic from an O-ring groove or from a pipe thread. Groove dimensions are covered in the note on O-ring grooves and seal glands, and thread form in the note on pipe threads on gas-equipment components. One of those notes does not invent the others. If the face and the thread must be concentric, that relationship is stated rather than assumed, as discussed in the note on concentricity of threads and seats.
Roughness and flatness are inspected as specified
Ra or another roughness call-out on the face is inspected by the method the print or the order names, at the location it names. A shop habit of “facing until it looks bright” is not a substitute. Flatness, a sealing-land width, or a restriction on turning marks and pits belongs in the same plan when it is specified. If a lapped or polished condition is required, it should be written down, because a standard turned face and a lapped face are not the same route.
Edges of the face matter. A sharp corner that will cut a gasket, a broken edge that reduces the land, or a burr left after threading can all be out of specification even when the roughness reading in the centre of the face is acceptable. Those edge conditions are taken from the revision, not dressed by habit after inspection.
Material, finish and protection of the face
The material of the stub, including the brasses and steels commonly seen on European gas-equipment prints, stays with the revision, as in the note on materials and finishes on gas-equipment prints. A coating or a passivation, if specified, has to be compatible with the face; a deposit on a sealing land is not added silently, and a face that must remain uncoated is masked only when the print or the order says so. Related masking comments, written for fasteners, follow the same idea in the note on partial coating and masking.
Packing that protects the face — caps, trays, or a cleanliness requirement — is included when it is specified, as in the note on packing, labelling and lot traceability. It is not assumed from the mere presence of a sealing face.
What a good face does not claim
Inspection of the face is inspection of a component characteristic. It is not a leak test of a regulator, a tightness test of a station, or evidence of a PED or type approval. If a pressure or tightness check on the part is itself required, that is a separate item and has to be named on the order; it still does not convert the stub into a complete device. Certificates and any EN 10204 3.1 evidence are confirmed per order when required.
Route and first article
Turning, facing, and any secondary lapping or polishing follow the agreed route. A change of method after samples have been approved is a process change. First-article inspection, when required, should report the face as it will be produced in series, as in the note on first-article inspection. A hand-polished prototype face does not by itself approve a later standard turning route if the roughness or the land will change.
Conflicts and volume
A print that names a roughness the chosen facing route cannot consistently meet, or that places a mark or a machining witness on the sealing land, is flagged. Conflicting faces in a title-block note and a detailed view are reviewed together. Those conflicts are resolved on the revision, not by polishing a land after a failed inspection and shipping it as the approved condition. Related marking limits are discussed in the note on marking on gas-equipment components.
Volume and the proposed route belong in the enquiry. A hand-lapped prototype face and a production turned face must be compared honestly at first article if both are proposed. A family of stubs that differ only by length still needs a current revision for each item; a face approved on one length is not automatic approval of the face on another if the setup or the datum changes.
What to send with the RFQ
Send the current drawing revision with a clear view of the sealing face, including roughness and geometric tolerances, together with the material, finish and volume. If a tightness check, a particular protection of the face, or a first-article layout is already required, say so. Unspecified points will be flagged before production rather than assumed.
This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.