A lubricant, a dry-film, a wax, a seal with a friction modifier, or a similar additional finish can be part of a made-to-print fastener. When the current revision or a referenced specification includes it, that finish is a requirement. It is not an informal assembly aid that can be added on the line “to help the nut start”, and it is not omitted because the thread and the coating would already look complete without it. The quotation follows the named lubrication or friction condition, not a shop preference.

What has to be visible on the revision

A complete call-out names the lubricant or dry-film, or the customer specification that defines it, the condition in which it is applied (over which coating, on which surfaces), and any friction class, coefficient or torque-tension requirement. “Light oil for assembly” or “lube as usual” without a specification is not complete. If a standard already defines the friction class and the accepted modifiers, it should be named on the revision or attached to the enquiry. The relationship between finish and torque-tension is already discussed in the note on friction class and torque-tension.

The modifier sits on top of a coating system that still has to be named. A dry-film does not identify whether the underlying deposit is a flake, a zinc-nickel or another finish, and a change of underlying system can change how the modifier behaves. Colour and a slightly oily appearance likewise do not identify the product, as in the note that colour is not the coating system.

Informal oiling is not a made-to-print step

Oiling “to help assembly”, a workshop wax, or a rust-preventive oil that is not in the specification is not part of the agreed route unless the specification allows it. Those informal films can change gauge feel, contamination, cleanliness and IMDS content. If a temporary protective oil is required for transit and must be removed before coating or assembly, that step belongs in the route, as in the note on cleanliness and washing. Adding, changing or omitting a specified lubricant after samples have been approved is a process change and is re-validated before serial release.

Inspection and functional checks

Friction, torque-tension, a prevailing-torque check, appearance, or a simple presence check of a dry-film are used when the print or the order requires that evidence, not automatically in every possible form. If a particular test, a coefficient window, or a first-article assembly check is already decided, name it. A bolt that “feels smooth” is not a substitute for a friction class written on the print. Certificates and any EN 10204 3.1 evidence are confirmed per order when required.

Open items and conflicts

A print that names a tight friction class and also “oil as required”, or that requires post-coat thread gauging and a heavy dry-film without saying which condition is gauged, is flagged. An IMDS entry, when required, has to include the specified lubricant or dry-film, as in the note on IMDS entries and the material grade.

Where the film is applied is part of the call-out

A modifier may be required on the thread only, on the bearing face, on the whole part, or on a named zone. That distribution is taken from the print or the specification. A dip of the whole basket “to be sure” is not a substitute for a thread-only call-out, and a dry-film that is missing from the bearing face is not excused because the thread looks coated. Partial application, when it is intended, should be as visible as any other partial finish, as in the note on partial coating and masking.

Volume and the proposed application route also belong in the enquiry. A hand-applied prototype film is not automatic approval of a later bulk route, and a change of product, of under-coat, or of application method after samples have been approved is a process change. First-article inspection, when required, should be planned on the production-intent finish, including any torque-tension or gauge condition, as in the note on first-article inspection. The current drawing revision remains the source of the lubrication requirement in every case.

The enquiry should also say whether any torque-tension, coefficient, or prevailing-torque check is required on the lubricated condition, and whether thread gauging is done before the modifier, after it, or both. Those conditions are not interchangeable. A dry-film that helps assembly can still spoil a tight gauge, and a light oil that is harmless to a gauge can still move a friction class. If a particular product name or a customer-approved list already exists, attach it; a neighbouring lubricant is not assumed to be equivalent. Related internal-thread effects are discussed in the note on coating on internal threads.

Packing and storage can wipe, transfer or contaminate a lubricant film. If the modifier is a controlled characteristic, packing belongs in the agreed route, as in the note on packing, labelling and lot traceability. A film that looked even at the coating line is not assumed to arrive in the same condition unless handling is part of the plan. Informal re-oiling in the stores is still not a made-to-print step.

What to send with the RFQ

Send the current drawing revision, the coating specification, and any friction-class or lubricant specification already chosen. If torque-tension or a first-article assembly check is required, say so. Volume belongs in the enquiry. Unspecified points will be flagged before production rather than assumed.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.