A weld nut is often located in the panel by a pilot, a collar, or another feature that sits in a prepared hole before the customer’s weld is made. Those features are part of the component drawing. They are not a licence to treat the nut as a welded assembly, and they are not interchangeable with the weld projections already discussed in the note on weld projections and location features. On a made-to-print order the pilot diameter, length, chamfer and fit to the hole are taken from the current revision, not from a catalogue type that happens to look similar.

What has to be visible on the revision

A complete call-out names the pilot diameter and its tolerance, the length or protrusion relative to the bearing face or the weld plane, any chamfer or undercut at the end of the pilot, and the hole or panel condition the feature is intended to enter. If the pilot is a through-bore, a short collar, or a stepped diameter, that form has to be drawn. “Add a pilot to suit the hole” is not complete. The body outline and the weld-projection layout are separate characteristics; a note on one of them does not invent the others, as already set out for weld nuts produced from the print.

Fit language has to be unambiguous. A transition fit, a clearance in the hole, or a light press before welding will not produce the same diameter. If the customer specification already defines the hole size and the allowable gap, that document should be named on the revision or attached to the enquiry. A familiar type code, including any SH- example used only as an illustration, is not a substitute for those figures.

Pilot length, chamfer and the weld plane

Pilot length is measured from a stated origin. A length taken from the underside of the nut, from the weld face, or from a locating shoulder will not be the same. If the print shows a maximum projection through the panel, that limit is inspected as drawn; it is not shortened or lengthened to make feeding easier unless the revision is changed. Chamfers and lead-in radii belong on the same revision, because they affect both entry into the hole and the amount of material left at the end of the pilot.

Relationship to the weld plane matters. A pilot that is concentric with the thread and flush with the weld face is a different part from one that stands proud or is set back. If runout or position of the pilot relative to the thread or the body is controlled, those geometric tolerances are part of the inspection plan, not optional shop practice. Related comments on screw and stud pilots, which are a different family of features, are in the note on point styles, chamfers and pilots; they do not define a weld-nut pilot.

What is not included as an assembly

The customer’s welding process, fixture, current, and panel preparation remain the customer’s, unless a written agreement says otherwise. SUNHY quotes the nut as a component. A statement that the pilot “must locate in the hole” describes a manufactured geometry; it does not include welding the nut to a panel, setting weld parameters, or guaranteeing a welded joint. The same boundary is used for weld screws and weld-stud elements.

If the thread must still gauge after the customer’s weld, that condition is a separate requirement and is discussed in the note on thread condition after welding. It is not implied by the presence of a pilot. Masking, thread plugs, or a post-weld gauge check are included only when the order says so.

Inspection of the locating feature

Pilot diameter, length, chamfer and, where specified, position or runout are inspected as characteristics of the loose nut. A go/no-go ring, a height gauge, or a layout against a ballooned drawing is used when the print or the order requires that method, not automatically in every possible form. A nut that “sits in a sample hole” on the bench is not evidence that the diameter and length on the revision have been met, unless that check is itself the agreed method and the hole is a controlled gauge.

First-article inspection, when required, should be planned on the production-intent route, including the heading or machining method that produces the pilot. A fully machined prototype with a turned pilot does not by itself approve a later headed route if the diameter, fillet or end condition will change. That process-change rule is the same as in the notes on first-article inspection and on cold-heading tooling.

Conflicts and incomplete enquiries

A print that names a tight pilot in a hole that the panel drawing does not support, or that mixes a catalogue body with a pilot taken from a different type, is flagged. Conflicting lengths in a title block and a specification attachment are reviewed together; one is not used to overwrite the other on the shop floor. If orientation or feeding features are also required, they belong on the same revision, as in the note on orientation and feeding features.

What to send with the RFQ

Send the current drawing revision of the nut, the panel or hole data if the fit is defined there, and any standard that describes the locating feature. If a first-article layout of the pilot is already required, say so. Volume and the proposed route also belong in the enquiry, because a headed pilot and a machined pilot do not always present the same end condition. Unspecified points will be flagged before production rather than assumed.

This article is a capability and commercial note. It is not a certificate, a dimensional data book, or evidence of customer approval. Catalogue type codes and example grades do not replace the customer’s item number, material specification or drawing revision.